-
Этот экземпляр BT-C100 подходит для аккумуляторов длиной от 40 мм!
(Ход салазок начинается от 40 мм)
Заряд/Разряд/Восстановление (для Ni-Mh)/Тест емкости на разряде/Тест внутреннего сопротивления.
Li-Ion, LiFePO4 (Три режима отсечки, переключение зажатием кнопки MODE - 3,6/4,2/4,35V) - до 32650.
Ni-Mh (1,48V) AA/AAA/C/D.
Заряд 200/300/500/700/1000/1300/1600/2000 mA.
Ток заряда может быть выбран в интервале 200 mA до 2000 mA для 1.2V Ni-Mh аккумулятора, для Li-Ion аккумулятора максимальный ток заряда - 1600 mA (питание от блока питания 12В 1А). При питании от порта USB (5V) зарядный ток для Li-Ion будет ограничен значением 1300 mA.
Разряд 100/200/300/500/700/1000 mA.
Максимальный ток разряда для Li-Ion - 700 mA.
Разряд 100/200/300/500/700/1000 mA.
Подсветка (неотключаемая).
Вход: 12-16V DC / 5V (microUSB).
POWERBANK (USB output auto detect): 5V до 2,1A.
Комплект поставки: зарядное устройство, сетевой блок питания (выход 12V 1A), инструкция.
Упаковка: коробка.
Гарантийный срок: 1 год.
1. Selectable charging current from 200mA to 2000mA at user’s choice for different batteries( Li-ion battery maximum charging current limited to 1600mA charging and 700mA for discharging due to heat control reason).
2. Charger can handle NiMH,Li-Ion batteries( AA, AAA, C, D , 14340 to 26650 protected or unprotected). 3.2v, 3.7v and 3.85v Li-ion battery type can further be selected by pressing "SET" button longer than 6s.
3. USB output for 5v/2.1 with auto load detection for apple devices. Digital USB output monitoring function available for USB output voltage, current or Ah. High efficency (>90%) for USB output. Automatically detects over current loading( when load current is over 2.5A) and battery voltage is low ( at 3.0v).
4. 16 bit Sigma-Delta AD converter monitors accurate minus delta voltage (-ΔV) for precise charging termination condition.
5. temperature sensors used to monitor battery and controller board working condition to achieve high reliability. when high temperature is detected at high working current ( >1000mA), working current will be automatically reduced preventing charger from over heating.
6. Battery impedance measurement.
7. Four Working Mode Available at User's Choice: Charge, Discharge, Test,Quick Test and Refresh.
8. Easy Read LCD with back light Showing Battery Voltage, Charge/Discharge Current, Charging Time, Battery Capacity etc.
9. Automatically find out battery type and using properait charging or discharging alogrithm.
10. Operating temperature: 0℃ - 45℃
11. Maximum charging capacity 20.00Ah or working time is over 100hour.
12. 12V/1A or 5V/2A external power adapter for reliable charging performance.( Car power adapter cord can be packed into the same box, this quotation is not including this car power adapter cable). When 5V power attached, charger will reduce li-ion charging current maximum to 1000mA automatically.
High Compatibility
Li-ion: 3.7V and 3.85V batteries (with size from 10440 to 32650)
NiMH / NiCd: AA, AAA, C, D
LiFeO4
2.1A USB Output
● Only for Li-ion batteries
● Output mode is automatically selected according to the device attached
● Output parameters are measured and displayed on LCD
Working Mode
4 working modes for Li-ion: Charge, discharge, test and impedance test
5 working modes for NiMH: Charge, discharge, test, refresh and impedance test
● Charging current can be selected from 200mA to 2000mA (NiMH and Li-ion)
● Discharging current can be selected from 100mA to 1000mA
● For Li-ion batteries, if charging current is over 1000mA, its CV charging terminate current is 100mA. If charging current is less than 1000mA, its CV terminate current is 50mA
● 0dv and –dv is automatically selected according to NiMH battery status to ensure battery is fully charged
Over heat protection
When temperature is over 60 degree centigrade, working current will be reduced until the condition is improved. If temperature is up to 75 degree centigrade, charger will shut down working process until temperature is lower than the safe limit
Parameter:
Input: DC 5 - 16V
Output: 0.8 - 5.5V
USB output: 5.0V 2.1A
Operation:
BAT Button
● Short press: LCD displays V, A, mAh, H (time), and MR (impedance)
● Long press for more than 2s to select working mode: Charge - discharge - test - refresh (only for NiMH) - impedance test. Press BAT to select working mode, and press USB to select working current
● Long press for more than 6s to activate Li-ion battery mode. Power up default 3.7V Li-ion batteries. Press BAT to select battery type, and press USB to exit and start to work
USB Button
● Short press: Switch from showing A (current) and Ah (ampere hour) for USB output
● Long press for more than 2s to activate USB output functionSpecifications
Type: Charger
Brand: Opus
Plug: USB
Charging Cell Type: NiCd,Ni-MH,LiFePO4
Compatible: 18490,C,D,26650,14500,16340,32650,17670,10440,22650,17500,17335,AA,AAA
Rechargeable Battery Qty: 1
Input Voltage: DC 5-16V
Output Voltage: 0.8-5.5VCharge Control Methods: CC (Constant-current),CV (Constant-voltage),Trickle Charge,-dV/dt
LCD screen: Yes
Circuit Detection: Yes
Protected Circuit: YesProduct weight: 0.086 kg
Package weight: 0.110 kg
Product size (L x W x H): 13.200 x 4.200 x 4.000 cm / 5.197 x 1.654 x 1.575 inches
Package size (L x W x H): 14.200 x 5.200 x 5.000 cm / 5.591 x 2.047 x 1.969 inchesPackage Contents: 1 x Opus BT-C100 Battery Charger
Бонус за отзыв: 20 руб. однократно для каждого товара при условии, что Вы купили этот товар (необходимо зарегистрироваться или войти)
Зарегистрируйтесь, чтобы создать отзыв.